Diff: README.txt

Revision:

1:edd760d6380f

Parent:

0:721af8bb4b69

--- a/README.txt	Wed Sep 29 11:39:40 2021 +0000
+++ b/README.txt	Thu Sep 30 11:58:20 2021 +0100
@@ -1,45 +1,38 @@
 Evaluation Boards/Products Supported
 ------------------------------------ 
-EVAL-AD1234 (AD1234)
-EVAL-AD1256 (AD1256)
-<< add more here >>
- 
+-Products supported: AD4695, AD4696
+-EVAL-AD4696FMCZ
+
+
 Overview
 --------
-These code files provide drivers to interface with AD1234 and communicate with 
-EVAL-AD1234 board. This code was developed and tested on SDP-K1 controller board 
-https://os.mbed.com/platforms/SDP_K1/. 
- 
-Product details: https://www.analog.com/en/products/ad1234.html
-Eval board details: https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/EVAL-AD1234.html
- 
- 
+This is an IIO ecosystem based firmware application to evalute the AD4696 family ADCs.
+The ADI developed ARM Mbed SDP-K1 controlled board acts as a target device, where firmware application is running.
+The ARM GCC/ARMC compiler is used for firmware development on ARM Mbed platform.
+The EVAL-AD4696FMCZ board is interfaced with SDP-K1 (or any Arduino compatible board) controller board using on-board Arduino Headers.
+
+
 Hardware Setup
 --------------
-Required: SDP-K1, EVAL-AD1234, USB cable, 12 V power supply, 60 MHz external 
-clock supply.
-Plug in the EVAL-AD124 board on SDP-K1 board (or any other Mbed enabled 
-controller board) using the SDP connector and screws.
-Connect SDP-K1 board to the PC using the USB cable.
- 
- 
+Refer "Hardware Connections" section from below wiki page link:
+https://wiki.analog.com/resources/tools-software/product-support-software/ad4696_mbed_iio_application
+
+
 How to Get Started
 ------------------
 Open Mbed online compiler. https://ide.mbed.com/compiler
-Import Code into compiler from here: https://os.mbed.com/teams/AnalogDevices/code/EVAL-AD1234/
-instructions on how to import code are here: https://os.mbed.com/docs/mbed-os/v5.12/tools/importing-code.html
-Compile code. Drag and drop binary into SDP-K1 controller board. Find detailed instructions 
-here: https://os.mbed.com/docs/mbed-os/v5.12/tools/getting-your-program-on-your-board.html
-Open Tera Term (or alternative), select 9600 baud rate, and the applicable COM port to see the 
-list of options.
- 
-A detailed user guide on how to use SDP-K1 board on Mbed platform is available 
-here: https://wiki.analog.com/resources/tools-software/mbed
- 
- 
+Import Code into compiler. Instructions on how to import code are here: https://os.mbed.com/docs/mbed-os/v6.8/quick-start/build-with-the-online-compiler.html
+Compile code to generate binary file and then drag and drop binary into SDP-K1 controller board. Detailed instructions are here:
+https://os.mbed.com/docs/mbed-os/v6.8/build-tools/getting-your-program-on-your-board.html
+
+Refere project wiki page to find detailed guide on how to use firmware:
+https://wiki.analog.com/resources/tools-software/product-support-software/ad4696_mbed_iio_application
+
+
 Notes
 -----
-If using Win 7, install serial drivers for Mbed. https://os.mbed.com/docs/mbed-os/v5.12/tutorials/windows-serial-driver.html
+Refere this page for latest documentation on Mbed-OS: https://os.mbed.com/docs/mbed-os/v6.8/introduction/index.html
 A detailed user guide on SDP-K1 controller board is available here https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/SDP-K1.html.
- 
-            
\ No newline at end of file
+
+
+Copyright (c) 2021 Analog Devices, Inc.  All rights reserved.
\ No newline at end of file