The B-L072Z-LRWAN1 LoRa®Discovery kit is a development tool to learn and develop solutions based on LoRa®and FSK/OOK technologies.
Table of Contents
The B-L072Z-LRWAN1 LoRa®Discovery kit is a development tool to learn and develop solutions based on LoRa®and FSK/OOK technologies. This Discovery kit features an all-in-one open module CMWX1ZZABZ-091 (by Murata). The module is powered by an STM32L072CZ and an SX1276 transceiver. The transceiver features the LoRa®long-range modem, providing ultra-long-range spread spectrum communication and high interference immunity, minimizing current consumption. Since CMWX1ZZABZ-091 is an open module, user has access to all STM32L072 peripherals such as ADC, 16-bit timer, LP-UART, I2C, SPI and USB 2.0 FS (supporting BCD and LPM).
The B-L072Z-LRWAN1 Discovery kit includes an ST-LINK/V2-1 embedded debug tool interface, LEDs, push-buttons, antenna, Arduino™Uno V3 connectors and USB OTG connector in Micro-B format.
- CMWX1ZZABZ-091 LoRa® module with STM32L072CZ
- ARM® 32-bit Cortex®-M0+ CPU
- 32 MHz max CPU frequency
- VDD from 1.65 V to 3.6 V
- 192 KB Flash
- 20 KB SRAM
- GPIO (40) with external interrupt capability
- General-purpose Timer (4)
- Basic Timer (2)
- Low Power Timer
- SPI (6)
- I2C (3)
- USART (4)
- Low-power UART
- USB 2.0 full-speed
- 12-bit ADC with 13 channels
- 12-bit DAC (2) with 1 channel each
- Comparators (2)
- Capacitive sensing channels (19)
- Random Generator (TRNG for HW entropy)
- Two types of extension resources
- Arduino Uno Revision 3 connectivity
- STMicroelectronics extension pin headers for full access to all STM32 I/Os
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Selection-mode switch to use the kit as a standalone ST-LINK/V2-1
- Flexible board power supply
- USB VBUS or external source (3.3 V, 5 V, 7 - 12 V)
- Power management access point
- User LED (LD1, LD2, LD3, LD4)
- Two push buttons: USER and RESET
- USB re-enumeration capability: three different interfaces supported on USB
- Virtual Com port
- Mass storage (USB Disk drive) for drag'n'drop programming
- Debug port
These headers give access to all STM32 pins.
Only the labels written in blue/white or green/white (i.e. PA_4, PB_5, A0, D14, LED1...) must be used in your code. The other labels are given as information (alternate-functions, power pins, ...).
You can find more details on the available pins and labels in the following files (link to the latest mbed-dev library version):
ST X-NUCLEO boards¶
Other Non-ST boards¶
For more information, please refer to:
The following section describes known limitations of the platform. Note that general issues are tracked into the mbed repository available on GitHub.
- There is no AnalogIn on Arduino A1, A3, A4, A5 pins.
- There is no PWM on Arduino D3, D5, D6, D9 pins.
- In order to use Serial (TX and RX) on Arduino D0 and D1 pins, you have to remove SB28 and SB29 solder bridges. In this case you will lose the ST-Link connection.